TDS510 Driver

Introduction Overview Wintech TDS510USB JTAG Emulator is designed to use with digital signal processors (DSPs) operating at 1.0-5.0 volts. The emulator itself is a bus-powered USB device. It is fully plug and play compatible and is fully powered by the host computer’s USB connection. The TDS510USB JTAG Emulator operates with TI Code Composer Studio IDE debug tool and is fully compatible with Windows 98/SE/ME/2000/XP. Features Wintech TDS510USB JTAG Emulator has the following features: z Supports Texas Instruments DSP with a JTAG (IEEE 1149.1) interface: C240X, F28X, VC33, C5000, C6000, TMS470 (ARM) and OMAP platforms. z Supports Texas Instruments Code Composer Studio. z Supports 1.0-5.0 volt DSP devices. z USB compatible. Simple Connection, fully Plug-and-Play compatible – no jumpers, no switch settings. z Hot pluggable z Power provided by the USB bus, no additional power supply is required. TDS510USB JTAG Emulator Installation Guide 4 QUICK Installation Quick Install Procedures This guide describes the steps to installing the TDS510USB JTAG Emulator in the following order: 1. Install the TDS510USB JTAG Emulator hardware 2. Install the TDS510USB JTAG device driver 3. Make sure Code Composer Studio IDE is installed on the PC 4. Install the TDS510USB JTAG Emulator software 5. Configure Code Composer Studio IDE 6. Reset the TDS510USB JTAG Emulator and Reset the target DSP 7. Run CCS The TDS510USB JTAG Emulator kit contains: z TDS510USB JTAG Emulator z USB interface cable z The TDS510USB driver disk. z TDS510SB2.0 JTAG Emulator Installation Guide Reference Guide (this document) Installation Requirements z Code Composer Studio IDE 1.2 or greater z A free USB port z 233MHz or higher Pentium compatible CPU (500MHz or higher Pentium III CPU or equivalent is recommended) z Local CD-ROM drive Supported Operating Systems z Windows 98/ME/2000/XP TDS510USB JTAG Emulator Installation Guide 5 Detailed Installation What you will need The following detailed list contains all items needed to install and run with the TDS510USB JTAG Emulator. z PC with a free Universal Serial Bus (USB) port. z Wintech TDS510USB JTAG Emulator z Wintech TDS510USB driver disk. z USB interface cable. z DSP target system z Code Composer Studio The Hardware Installation z Remove power from the target DSP system. z Connect the keyed TDS510USB JTAG Emulator JTAG interface cable to the target board. z Apply power to the target DSP system. z Connect the TDS510USB JTAG Emulator to the host computer system using a USB cable. WARNING Be sure to connect interface cables with the correct orientation. Pin 1 on the interface cable should match Pin 1 on the DSP system connector. The Wintech TDS510USB 2.0 JTAG Emulator features a "keyed" connector to minimize your chance of error. Do not force cables into position. Forcing them may cause damages on the cables or the interconnected boards and 510USB JTAG Emulator Installation Guide 6 The USB Device Drivers Installation A. Driver installation for Windows 2000/XP: 1. After plug the TDS510USB JTAG Emulator into the host computer's USB port, the system should display the Found New Hardware (Figure A-1) dialog box. This dialog box indicates the computer operating system has found a new USB device. Figure A-1 2. The system will prompt for new hardware detected and start the “Found New Hardware Wizard” as shown in Figure A-2. Figure A-2 3. Click on Next and system will display the window as shown in Figure 510USB JTAG Emulator Installation Guide 7 Figure A-3 4. Check on “Search for a suitable driver for my device (Recommended)” and click on Next. The system will display a window as shown in Figure A-4. Figure A-4 5. Check on “CD-ROM drives” and click on Next. The system will prompt you to insert the manufacturer’s installation disk, as shown in the Figure 510USB JTAG Emulator Installation Guide 8 Figure A-5 6. Click on Browse and locate the file in the installation CD, or in the folder where you have download the file into, as shown in Figure A-6. Figure A-6 7. Click on Next, the following window will be displayed, as shown in Figure A-7. Figure A-7 8. Click on Finish. Setup is completed. TDS510USB JTAG Emulator Installation Guide 9 B. Driver installation for Win98/ME: 1. After plug the TDS510USB JTAG Emulator into the host computer's USB port, the system should display the Found New Hardware (Figure B-1) dialog box. This dialog box indicates that the computer operating system has found a new USB device. Figure B-1 2. The system should detect the new hardware and start the “Add New Hardware Wizard”, as shown in Figure B-2. Figure B-2 3. Click on Next to go to the next window, as shown in Figure B-3. TDS510USB JTAG Emulator Installation Guide 10 Figure B-3 4. Click on Next to go to the next window, as shown in Figure B-4. Figure B-4 5. Click on OK and the wizard will display the driver to be installed, as shown in Figure 510USB JTAG Emulator Installation Guide 11 Figure B-5 6. Click on Next and the wizard will complete the driver installation and display the window as shown in Figure B-6. Figure B-6 7. Click on Finish. Setup is completed TDS510USB JTAG Emulator Installation Guide 12 Installing the TDS510USB Software This installation assumes that the Code Composer Studio IDE has already been installed on the PC. If not, please follow the directions for installing Code Composer Studio firsts