推荐星级:
  • 1
  • 2
  • 3
  • 4
  • 5

CFX-仿真软件在天线设计中的应用

更新时间:2019-08-13 07:05:38 大小:1M 上传用户:杨义查看TA发布的资源 标签:cfx仿真软件天线 下载积分:1分 评价赚积分 (如何评价?) 收藏 评论(0) 举报

资料介绍

文档为CFX-仿真软件在天线设计中的应用总结文档,是一份不错的参考资料,感兴趣的可以下载看看,,,,,,,,,,,,,,

部分文件列表

文件名 大小
CFX-仿真软件在天线设计中的应用.pdf 1M

部分页面预览

(完整内容请下载后查看)
4, 3, 6-11  
Published Online February 2014
Application of CFX Software in the Design of Antenna  
Songdong Fan, Huabing Su  
Comba Telecom Systems (Guangzhou) Co., Ltd., Guangzhou  
Email:
Received: Dec. 18th, 2013; revised: Dec. 29th, 2013; accepted: Jan. 4th, 2014  
Copyright © 2014 Songdong Fan, Huabing Su. This is an open access article distributed under the Creative Commons Attribution License, which  
permits unrestricted use, distribution, and reproduction in any medium, provided the original work is properly cited. In accordance of the Creative  
Commons Attribution License all Copyrights © 2014 are reserved for Hans and the owner of the intellectual property Songdong Fan, Huabing Su. All  
Copyright © 2014 are guarded by law and by Hans as a guardian.  
Abstract: In order to establish the mathematical model and simulation analysis for antenna by using fluid dynamics  
simulation software CFX, the data from simulation have been compared with the data from the lab experiment on an-  
tenna wind tunnel. With the results reflecting the actual situation of the wind load of antenna, it is important to provide a  
theoretical basis for the calculation of wind load of antenna structure.  
Keywords: Antenna; Wind Load; Wind Resistance Coefficient; Wind Tunnel Experiment; Computational Fluid  
Dynamic Simulation Software CFX  
CFX 仿真软件在天线设计中的应用  
范颂东,苏华冰  
京信通信系统(广州)有限公司,广州  
Email:
收稿日期:2013 12 18 日;修回日期:2013 12 29 日;录用日期:2014 1 4 日  
通过采用计算流体动力学仿真软件 CFX 对天线建立数学模型和仿真分析仿真结果数据与天线风洞  
实验数据进行归纳对比,发现结果能够反映出实际天线的风载状况,能为天线结构风载荷计算提供理论依据。  
关键词:天线;风载荷;风阻系数;风洞实验;计算流体动力学仿真软件 CFX  
1. 引言  
越来越多样化的情况下,已不能适应瞬息万变的市场  
要求。  
随着手机的普遍使用,基站天线的应用也已迅速  
随着各种计算机辅助设计软件的应用,采用计算  
推广。对于基站天线结构而言,合理的设计应该确保  
流体动力学软件 CFX 对天线结构进行设计分析已成  
在各种环境下使天线精确地保持形状和姿态前,  
为可能,从而可以大幅度提高设计质量和效率。  
在基站天线的结构设计中,关键就是在风载荷作用下  
本文主要介绍了采用计算流体动力学软件 CFX  
建立目标天线模型的流体动力学模型,进行风载荷流  
体动力学仿真,得出各类天线模型的风阻系数及不同  
风速下的风载荷,并与风洞实验的结果相互对比验证,  
建立一个可模拟风洞实验效果的动力学仿真平台,为  
各类天线的外形结构设计提供理论依据。  
设计模型的建立及在此基础上进行的刚度强度分析  
和变形的计算。以往多采用经验类比设计与传统材料  
力学简化计算相结合,或是静力学模型仿真分析,但  
这些方法在很大程度上取决于设计人员的经验和不  
能完全反映天线的实际风载状况,往往使设计偏于保  
守,致使产品重量大,成本高,尤其在当前客户要求  
OPEN ACCESS  
6

全部评论(0)

暂无评论